Discontinued (Discontinued) BE2872 (Expired) Beryllium nitrate powder (CAS 13597-99-4)

SECTION 1. IDENTIFICATION

Product Name: Beryllium Nitrate

CAS #: 13597-99-4

Relevant identified uses of the substance: Scientific research and development

Supplier details:

Stanford Advanced Materials

E-mail: sales@samaterials.com

Tel: (949) 407-8904

Address: 23661 Birtcher Dr., Lake Forest, CA 92630 U.S.A.

SECTION 2. HAZARDS IDENTIFICATION

Physical hazards Oxidizing solids Category 2

Health hazards Acute toxicity, oral Category 3

Acute toxicity, inhalation Category 2

Skin corrosion/irritation Category 2

Serious eye damage/eye irritation Category 2

Sensitization, skin Category 1

Carcinogenicity (inhalation) Category 1B

Specific target organ toxicity, single exposure Category 3 respiratory tract irritation

Specific target organ toxicity, repeated Category 1 (Respiratory system)

exposure

Environmental hazards Not classified.

OSHA defined hazards Not classified.

Label elements

Signal word: Danger

Hazard statement In contact with water releases flammable gas. Toxic if swallowed. Fatal if inhaled.

Causes skin irritation. Causes serious eye irritation. May cause an allergic skin reaction. May causecancer by inhalation. May cause respiratory irritation. Causes damage to organs (respiratory system)

through prolonged or repeated exposure by inhalation.

Precautionary statement

Prevention Obtain special instructions before use. Do not handle until all safety precautions have been

read and understood. Minimize dust generation and accumulation. Avoid breathing dust. Wash

thoroughly after handling. Do not eat, drink or smoke when using this product. Contaminated work

clothing must not be allowed out of the workplace. Wear protective gloves/protective clothing/eye

protection/face protection. In case of inadequate ventilation wear respiratory protection.

Response If swallowed: Immediately call a poison center/doctor. If on skin: Wash with plenty of water.

If inhaled: Remove person to fresh air and keep comfortable for breathing. If in eyes: Rinse

cautiously with water for several minutes. Remove contact lenses, if present and easy to do.

Continue rinsing. If exposed or concerned: Get medical advice/attention. If skin irritation or rash

occurs: Get medical advice/attention. Wash contaminated clothing before reuse. If experiencing

respiratory symptoms: Call a poison center/doctor.

Storage Store locked up. Store in a well-ventilated place. Keep container tightly closed.

Disposal Dispose of contents/container in accordance with local/regional/national/international

regulations.

Hazard(s) not otherwise

classified (HNOC)

None known.

SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Beryllium Nitrate

CAS number: 13597-99-4

SECTION 4. FIRST AID MEASURES

Inhalation

If symptoms develop move victim to fresh air. For breathing difficulties, oxygen may be necessary.

Breathing difficulty caused by inhalation of particulate requires immediate removal to fresh air. If

breathing has stopped, perform artificial respiration and obtain medical help.

Skin contact

Take off contaminated clothing and wash before reuse. Thoroughly wash skin cuts or wounds to

remove all particulate debris from the wound. Seek medical attention for wounds that cannot be

thoroughly cleansed. Treat skin cuts and wounds with standard first aid practices such as

cleansing, disinfecting and covering to prevent wound infection and contamination before

continuing work. Obtain medical help for persistent irritation. Material accidentally implanted or

lodged under the skin must be removed.

Eye contact

Immediately flush eyes with plenty of water for at least 15 minutes, lifting lower and upper eyelids

occasionally. Get medical attention if symptoms persist.

Ingestion

If swallowed, seek medical advice immediately and show this container or label. Induce vomiting

immediately as directed by medical personnel. Never give anything by mouth to an unconscious

person.

Most important symptoms/effects, acute and delayed

May cause allergic skin reaction. May cause allergic respiratory reaction. Prolonged exposure may

cause chronic effects.

Indication of immediate medical attention and special treatment needed

Treatment of Chronic Beryllium Disease: There is no known treatment which will cure chronicberyllium disease. Prednisone or other corticosteroids are the most specific treatment currently

available. They are directed at suppressing the immunological reaction and can be effective in

diminishing signs and symptoms of chronic beryllium disease. In cases where steroid therapy has had

only partial or minimal effectiveness, other immunosuppressive agents, such as

cyclophosphamide, cyclosporine, or methotrexate, have been used. In view of the potential side

effects of all the immunosuppressive medications, including steroids such as prednisone, they

should be used only under the direct care of a physician. Other treatment, such as oxygen, inhaled

steroids or bronchodilators, may be prescribed by some physicians and can be effective in

selected cases. In general, treatment is reserved for cases with significant symptoms and/or

significant loss of lung function. The decision about when and with what medication to treat is a

judgment situation for individual physicians.

SECTION 5. FIREFIGHTING MEASURES

Suitable extinguishing media

The product is non-combustible. Use extinguishing measures that are appropriate to local

circumstances and the surrounding environment.

Special protective equipment and precautions for firefighters

Firefighters should wear full protective clothing including self contained breathing apparatus. Wear

suitable protective equipment.

Fire fighting equipment/instructions

Move containers from fire area if you can do so without risk. Water runoff can cause environmental

damage. Do not use water to extinguish fires around operations involving molten metal due to the

potential for steam explosions.

Specific methods

Pressure-demand self-contained breathing apparatus must be worn by firefighters or any other

persons potentially exposed to the particulate released during or after a fire.

SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures

In solid form this material poses no special clean-up problems. Wear appropriate protective

equipment and clothing during clean-up.

Methods and materials for containment and cleaning up

Clean up in accordance with all applicable regulations.

Environmental precautions

Avoid release to the environment. In the event of a spill or accidental release, notify relevant

authorities in accordance with all applicable regulations. Prevent further leakage or spillage if safe

to do so. Avoid discharge into drains, water courses or onto the ground.

SECTION 7. HANDLING AND STORAGE

Precautions for safe handling

Obtain special instructions before use. Do not handle until all safety precautions have been read

and understood. Minimize dust generation and accumulation. Do not breathe dust/fume. Wear

protective gloves/protective clothing/eye protection/face protection. Wear respiratory protection.

Wash thoroughly after handling. When using, do not eat, drink or smoke. Contaminated work

clothing must not be allowed out of the workplace.

Conditions for safe storage, including any incompatibilitiesKeep locked-up. Avoid contact with acids and alkalies. Avoid contact with oxidizing agents.

SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Exposure guidelines

On July 14, 2020, the Occupational Safety and Health Administration (OSHA) issued the final

Beryllium Standard for General Industry (29 CFR 1910.1024) which includes a Permissible

Exposure Limit (PEL) of 0.2 μg/m3 as an 8-hour TWA. The Preamble to the OSHA Beryllium

Standards in 29 CFR Parts 1910, 1915 and 1926 states: “OSHA concludes that exposure to

beryllium constitutes a significant risk of material impairment to health and that the final rule will

substantially lower that risk. The Agency considers the level of risk remaining at the new TWA PEL

to still be significant. However, OSHA did not adopt a lower TWA PEL because the Agency could

not demonstrate technological feasibility of a lower TWA PEL. The Agency has adopted the STEL

and ancillary provisions of the rule to further reduce the remaining significant risk.”

Based on joint research conducted with the National Institute for Occupational Safety and Health

(NIOSH), Materion adopted an 8 element Beryllium Worker Protection Model (BWPM) which

includes the use of a recommended exposure guideline (REG) for airborne beryllium of 0.2 μg/m3

as a time-weighted average (TWA) limit for an 8-hour work day. Subsequent NIOSH studies have

shown that the BWPM has reduced but not eliminated the risk of beryllium sensitization and

chronic beryllium disease (CBD) in workers. Therefore, Materion recommends that beryllium users

not only comply with the OSHA Beryllium Standard and carefully apply all elements of the BWPM,

but reduce airborne exposures to the lowest feasible level. Information on the BWPM can be

found at www.berylliumsafety.com or by contacting Materion at +1 800.862.4118.

The American Conference of Governmental Industrial Hygienists (ACGIH®) is a scientific body

that has developed guidelines for all listed substances. In its development documents, the

ACGIH® states that “Threshold Limit Values and Biological Exposure Indices represent conditions

under which ACGIH® believes that nearly all workers may be repeatedly exposed without adverse

health effects. They are not fine lines between safe and dangerous exposures, nor are they a

relative index of toxicology.”

Specific genetic factors have been identified and shown to increase an individual’s susceptibility to

CBD. Medical testing is available to detect those genetic factors in individuals.

Appropriate engineering controls

Ensure adequate ventilation, especially in confined areas.

Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates

should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,

or other engineering controls to maintain airborne levels below recommended exposure limits. If

exposure limits have not been established, maintain airborne levels to an acceptable level.

Whenever possible, the use of local exhaust ventilation or other engineering controls is the

preferred method of controlling exposure to airborne particulate. Where utilized, exhaust inlets to

the ventilation system must be positioned as close as possible to the source of airborne

generation. Avoid disruption of the airflow in the area of a local exhaust inlet by equipment such as

a man-cooling fan. Check ventilation equipment regularly to ensure it is functioning properly.

Provide training on the use and operation of ventilation to all users. Use qualified professionals to

design and install ventilation systems.

Eye/face protection

Wear approved safety glasses, goggles, face shield and/or welder’s helmet when risk of eye injury

is present, particularly during operations that generate dust, mist or fume.

Hand protection

Wear gloves to prevent contact with particulate or solutions. Wear gloves to prevent metal cuts

and skin abrasions during handling.

Respiratory protection

When airborne exposures exceed or have the potential to exceed the occupational exposure

limits, approved respirators must be used as specified by an Industrial Hygienist or other qualifiedprofessional. Respirator users must be medically evaluated to determine if they are physically

capable of wearing a respirator. Quantitative and/or qualitative fit testing and respirator training

must be satisfactorily completed by all personnel prior to respirator use. Users of tight fitting

respirators must be clean shaven on those areas of the face where the respirator seal contacts the

face. Use pressure-demand airline respirators when performing jobs with high potential exposures

such as changing filters in a baghouse air cleaning device.

SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance

Physical state Solid.

Form Crystalline.

Color White. Yellow.

Odor Nitrogen Pentoxide Odor.

Odor threshold Not applicable.

pH Not applicable.

Melting point/freezing point 140.9 °F (60.5 °C) / Not applicable.

Initial boiling point and boiling range

Not applicable.

Flash point Not applicable.

Evaporation rate Not applicable.

Flammability (solid, gas) Flammable gas.

Upper/lower flammability or explosive limits

Explosive limit - lower (%) Not applicable.

Explosive limit - upper (%) Not applicable.

Vapor pressure Not applicable.

Vapor density Not applicable.

Relative density Not applicable.

Solubility(ies)

Solubility (water) Soluble.

Partition coefficient

(n-octanol/water)

Not applicable.

Auto-ignition temperature Not applicable.

Decomposition temperature Not applicable.

Viscosity Not applicable.

Other information

Density Not available.

Molecular formula Be.2H-N-O3

Molecular weight 133.03 g/mol

SECTION 10. STABILITY AND REACTIVITY

Reactivity Not available.

Chemical stability Not available.

Possibility of hazardous Not available.

reactions

Conditions to avoid Not available.

Incompatible materials Not available.

Hazardous decomposition products Not available.

SECTION 11. TOXICOLOGICAL INFORMATION

Information on likely routes of exposure

Inhalation May cause sensitization by inhalation. May cause allergy or asthma symptoms or breathing

difficulties if inhaled. May cause damage to organs (respiratory system) through prolonged or repeated

exposure.

Skin contact May cause an allergic skin reaction.

Eye contact Not likely, due to the form of the product.

Ingestion Not likely, due to the form of the product.

Symptoms related to the physical, chemical and toxicological characteristics

Respiratory disorder.

Information on toxicological effects

Acute toxicity May cause allergy or asthma symptoms or breathing difficulties if inhaled. May cause

allergic skin reaction.

Skin corrosion/irritation Not likely, due to the form of the product.

Serious eye damage/eye Harmful in contact with eyes.

irritation

Respiratory or skin sensitization

ACGIH sensitization

BERYLLIUM AND COMPOUNDS, SOLUBLE AND

INSOLUBLE COMPOUNDS, AS BE, INHALABLE

FRACTION (CAS 13597-99-4)

Respiratory sensitization

Respiratory sensitization May cause allergy or asthma symptoms or breathing difficulties if inhaled.

Skin sensitization May cause an allergic skin reaction.

Germ cell mutagenicity Due to lack of data the classification is not possible.

Carcinogenicity Cancer hazard.

IARC Monographs. Overall Evaluation of Carcinogenicity

Beryllium Nitrate (CAS 13597-99-4) 1 Carcinogenic to humans.

OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)

Beryllium Nitrate (CAS 13597-99-4) Cancer

US. National Toxicology Program (NTP) Report on Carcinogens

Beryllium Nitrate (CAS 13597-99-4) Known To Be Human Carcinogen.

Reproductive toxicity Not classified.

Specific target organ toxicity -single exposure

May cause allergy or asthma symptoms or breathing difficulties if inhaled.

Specific target organ toxicity -repeated exposure

May cause damage to organs (respiratory system) through prolonged or repeated exposure by

inhalation.

Chronic effects Hazardous by OSHA criteria. May cause damage to organs through prolonged or

repeated exposure.

Further information Symptoms may be delayed.

SECTION 12. ECOLOGICAL INFORMATION

Persistence and degradability No data is available on the degradability of this product.

Bioaccumulative potential Not available.

Mobility in soil Not available.

Other adverse effects Not available.

SECTION 13. DISPOSAL CONSIDERATIONS

Disposal instructions

Material should be recycled if possible. Disposal recommendations are based on material as

supplied. Disposal must be in accordance with current applicable laws and regulations, and

material characteristics at time of disposal. When this product as supplied is to be discarded as

waste, it does not meet the definition of a RCRA waste under 40 CFR 261.

Waste from residues / unused products

Empty containers or liners may retain some product residues. This material and its container must

be disposed of in a safe manner (see: Disposal instructions).

Contaminated packaging

Empty containers should be taken to an approved waste handling site for recycling or disposal.

Since emptied containers may retain product residue, follow label warnings even after container is

emptied.

SECTION 14. TRANSPORT INFORMATION

DOT

UN number UN2464

UN proper shipping name Beryllium nitrate

Class 5.1

Transport hazard class(es)

Subsidiary risk 6.1(PGI, II)

Label(s) 5.1, 6.1

Packing group II

Special precautions for user Not available.

Special provisions IB8, IP2, IP4, T3, TP33

Packaging exceptions 152

Packaging non bulk 212

Packaging bulk 242

IATA

UN number UN2464

UN proper shipping name Beryllium nitrate

Class 5.1

Transport hazard class(es)

Subsidiary risk 6.1(PGI, II)

Packing group II

Environmental hazards No.

ERG Code 5P

Special precautions for user Not available.

Other information

Cargo aircraft only Allowed with restrictions.

IMDG

UN number UN2464

UN proper shipping name BERYLLIUM NITRATE

Class 5.1

Transport hazard class(es)

Subsidiary risk 6.1(PGI, II)

Packing group II

Marine pollutant No.

Environmental hazardsEmS F-A, S-Q

Special precautions for user Not available.

SECTION 15. REGULATORY INFORMATION

US federal regulations This product is listed on the U.S. EPA TSCA Inventory.

Toxic Substances Control Act (TSCA)

TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)

Not regulated.

CERCLA Hazardous Substance List (40 CFR 302.4)

Beryllium Nitrate (CAS 13597-99-4) Listed.

SARA 304 Emergency release notification

Not regulated.

OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)

Beryllium Nitrate (CAS 13597-99-4) Cancer

lung effects (CBD and acute beryllium disease)

beryllium sensitization

respiratory tract irritation

SARA 302 Extremely hazardous substance

Superfund Amendments and Reauthorization Act of 1986 (SARA)

SECTION 16. OTHER INFORMATION

Safety Data Sheet according to Regulation (EC) No. 1907/2006 (REACH). The above information is

believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The

information in this document is based on the present state of our knowledge and is applicable to the

product with regard to appropriate safety precautions. It does not represent any guarantee of the

properties of the product.